Call Us Today (01702) 611027 9am - 5:30pm
Quick & Friendly Customer Service
Fast & Free Delivery
Order 2 spools B4 3PM Receive Next Day, Mon - Fri UK (Exc weekends)

PLA FilaPrint Premium

FilaPrint Glow in the Dark Green Premium PLA 1.75mm 3D Printer Filament

(3)

FilaPrint Glow in the Dark Green Premium PLA 1.75mm 3D Printer Filament

(3)
£21.46 £25.75 (inc. VAT)
Stock Status: In Stock
An easy to print Premium PLA, extremely low warp (if at all) slightly modified PLA to give your prints extra strength and durability. VAT will be added at checkout, though we have covered the cost of regular postage! Plus if you buy two spools before 2pm today you will receive them next day (within the UK, Weekdays only).
You Will Earn 25 points with this purchase

Make 6 weekly payments of £4.29.

Interest free. Learn More



A wonderful Glow in the Dark Green Premium PLA!  Low warp, easy to print.  1 Kilo of premium 3D Printer Filament, amazing value for money.
Coffin demo by : @offbeatprinting
"NOTE: Glow in the Dark filament should be removed from packaging and exposed to light for several hours  before turning out your lights to enjoy it's glowing effect."

This 1kg of filament spool is shrink wrapped, boxed and shrink wrapped yet again!  Ensuring that it arrives with you moisture free and ready to print.

Fantastic layer bonding, low temperature printing, (see 3D Benchy print sample in photo) no heated platform is necessary as it lays down beautifully on the majority of FFF/FDM 3D printer platform surfaces.

Superb tolerances with a smooth finish, a perfect compliment to your 3D printer.

Features:
  • Tougher and less brittle compared to regular PLA
  • Easy to print at low temperature
  • Little "warping"
  • biodegradable
  • Limited odor
Diameter Tolerance Roundness
1.75mm ± 0,05mm >95%
Characteristics Test Method Typical Value
Specific Gravity ASTM D1505 1,24 g/cc
MFI 6,0 g/10 min
Tensile Strength ASTM D882 110 MPa (MD)
145 MPa (TD)
Elongation at break ASTM D882 160 MPa (MD)
100 MPa (TD)
Tensile Modulus ASTM D882 3310 MPa (MD)
3860 MPa (TD)
Impact Strength 7,5 KJ/m²
Printing Characteristics Test Method Typical Value
Printing temperature 180-210ºc
Melting temperature 210±10ºc
Melting point ASTM D3418 145-160ºc

Looking for a new type of 3D printing surface that requires very little maintenance and will last for months, if not years!, then try the amazing PrintBite.
  • Filament Brand:
    FilaPrint
  • Filament Type:
    PLA
  • Filament Colour:
    Glow in the Dark Green
  • Filament Diameter:
    1.75mm
  • Filament Weight:
    1Kg
  • Brand:
    FilaPrint Premium PLA
  • Condition:
    New
  • Product Code:
    FPLA-GLOGRE-1.75mm
  • Weight:
    1kg
product review overlay image

Customer reviews

(3 Customer reviews)
Write a review

Great filament , make sure you have a steel nozzle

This is great filament, the glow is good and prints well , however it is abrasive, the first clue is feel the texture of the filament on the roll and as many or most Glow in the Dark filaments are abrasive thsi one is no exception. I ran it initially on a brass nozzle only because I have lots of replacements and I was lazy, it ripped through the nozzle in about a quarter of the roll so seriously make sure you have a steel nozzle installed. I can;t praise the filament enough though it really is great , the Glow lasts well and is bright, print properties the same as PLA as you would expect although I did find with the platform at 40 degrees it was much better adhesion.

Shaun Kemp | East Sussex | October 2021

glows well

had to run the temp a bit higher than i would do for pla 210 degrees on the nozzle and 50 on the bed

mike rogers | west mids | October 2021

Nice strong glow

Nice strong glow and like all of the Filaprint own brand prints really well.

Just be sure you have a suitable nozzle as Glow in the Dark can be abrasive.

Paul Songer | | October 2020