15% off our Fluorescent filament deal ends Midnight Tonight!

Get In Touch

Fill in your details below and click 'Submit'

FilaPrint Glow in the Dark Green Premium PLA 2.85mm 3D Printer Filament

Product Code: FPLA-GLOGRE-2.85-1kg
  • Filament Brand: FilaPrint
  • Filament Type: PLA
  • Filament Colour: Glow in the Dark Green
  • Filament Diameter: 2.85mm
  • Filament Weight: 1Kg
An easy to print Premium PLA, extremely low warp (if at all) slightly modified PLA to give your prints extra strength and durability. VAT will be added at checkout, though we have covered the cost of regular postage! Plus if you buy two spools before 2pm today you will receive them next day (within the UK, Weekdays only).
£23.35 Inc Vat
£19.46 Exc Vat


  • Availability: In Stock
  • You will earn 23 loyalty points with this purchase worth £0.23 that you can use on this order.

    More Details

    A wonderful Glow in the Dark Green Premium 2.85mm PLA!  Low warp, easy to print.  1 Kilo of premium 3D Printer Filament, amazing value for money.

    "NOTE: Glow in the Dark filament should be removed from packaging and exposed to light for several hours  before turning out your lights to enjoy it's glowing effect."​​​​​​​

    This 1kg of filament spool is shrink wrapped, boxed and shrink wrapped yet again!  Ensuring that it arrives with you moisture free and ready to print.

    Fantastic layer bonding, low temperature printing, (see 3D Benchy print sample in photo) no heated platform is necessary as it lays down beautifully on the majority of FFF/FDM 3D printer platform surfaces.

    Superb tolerances with a smooth finish, a perfect compliment to your 3D printer.

    • Tougher and less brittle compared to regular PLA
    • Easy to print at low temperature
    • Little "warping"
    • biodegradable
    • Limited odor
    Diameter Tolerance Roundness
    2.85mm ± 0,05mm >95%
    Characteristics Test Method Typical Value
    Specific Gravity ASTM D1505 1,24 g/cc
    MFI 6,0 g/10 min
    Tensile Strength ASTM D882 110 MPa (MD)
    145 MPa (TD)
    Elongation at break ASTM D882 160 MPa (MD)
    100 MPa (TD)
    Tensile Modulus ASTM D882 3310 MPa (MD)
    3860 MPa (TD)
    Impact Strength 7,5 KJ/m²
    Printing Characteristics Test Method Typical Value
    Printing temperature 180-210ºc
    Melting temperature 210±10ºc
    Melting point ASTM D3418 145-160ºc

    Looking for a new type of 3D printing surface that requires very little maintenance and will last for months, if not years!, then try the amazing PrintBite.

    Lars-Johan Kinnunen -
    4 Stars

    Prints very easily. On my Prusa i3 MK3 (I printed using the Prusa PLA profile) I didn't even have to add any adhesive to the print plate, and could still print at full speed, with perfect first layers. It was also easy to remove the prints when done. Remarkable. I tested charging the plastic using a UV torch, a cheap 12-LED, powered by 3 new AAA batteries. After one minute the filament glowed very strongly in the dark, with an eerie green colour. However, it did not glow for very long; after an hour it was almost completely dark again (but perhaps this is OK, considering it just got one minut of UV exposure). I deduce one star for the short glow time, but apart from that I think it's a very good product.