Igus® 3D Printing Filaments Home / Filaments / By Brand / Igus® 3D Printing Filaments / iglidur® I180-PF 3D Printing Filament 1.75mm 750gms White iglidur® I180-PF 3D Printing Filament 1.75mm 750gms White iglidur® I180-PF 3D Printing Filament 1.75mm 750gms White £79.00 £94.80 (inc. VAT) Stock Status: In Stock Versatile use: good combination of high wear resistance, strength and temperature resistant filament You Will Earn 94 points with this purchase Add to your Wish List Make 6 weekly payments of £15.80.Interest free. Learn More Information Specifications Reviews 3D printer filament: iglidur® |180-BL-PF Components made of igus® Tribo-Filament are up to 50 times more wear-resistant than standard materials for 3D printing and therefore have an extremely long service life. Due to their excellent tribological properties, they are suited for 3D printing of replacement parts, for example bearings, drive nuts, gears and other wear parts. The igus® Tribo-Filaments can be processed on 3D printers that are based on the fused-deposition-modelling method (FDM/FFF) and that allow the nozzle temperature to be set as required. Typical application areas: Special machine construction Jig construction Complex wear parts Tribological 3D Printing Filament Tribology is the science and engineering of interacting surfaces in relative motion. It includes the study and application of the principles of friction, lubrication and wear. Tribology is particularly important in today's world because so much energy is lost to friction in mechanical components. To use less energy, we need to minimize the amount that is wasted. Significant energy is lost due to friction in sliding interfaces. Iglidur I180 iglidur® I180 combines very high wear resistance with the highest strength of the iglidur® tribo-filaments Easier to process than iglidur® I170 and iglidur® J260 Processable on 3D Desktop printers, where standard ABS filaments are used Upon the processing the printer must be enclosed in a case and te cooling fan must be off Flexural strength: 46 / 33 MPa Versatile use: good combination of high wear resistance, strength and temperature resistance Good processing ability with an enclosed printer and igus adhesive film Colour black For a comprehensive overview of the Tribology filament specifications and tests view here. Tested strength when compared to machined and injection-moulded parts Up to 50 x higher abrasion resistance Test parameters - wear test swivelling Surface pressure: 1MPa Surface speed: 0.01m/s Pivoting angle: 60° Duration: four weeks Shaft materials: CF53 and 304 SS Test result: the pivot test shows that the abrasion resistance of the iglidur® filament is up to 50 times higher than the standard 3D printing materials (e.g. ABS). General properties Colour black Material suitable for Beginner Max. moisture absorption (at 23 °C/73 °F, 50% r.h.) 0.3 Wt.-%, test method DIN 53495 Max. water absorption 0.9 Wt.-% Net weight 250 g Coefficient of sliding friction, dynamic, against Cf53 steel 0.25 Coefficient of sliding friction, dynamic, against 304 stainless steel 0.21 pv value, max. (dry) 0.23 MPa ⋅ m/s Flexural strength 46 / 33 MPa Physical and thermal properties Max. long-term application temperature 80 °C Max. short-term application temperature 90 °C Lower application temperature -40 °C Thermal expansion coefficient (at 23°C/73°F) 9 K-1 ⋅ 10-5, test method DIN 53752 Heat conductivity 0.23 W/(m ⋅ K), test method ASTM C 177 Pressure load 59 MPa Max. recommended surface pressure (at +20 °C/68 °F) 30 MPa Requirements Mould-free according to DIN EN ISA 846 Procedure A No Processing instructions Nozzle temperature (min.) 250 °C Nozzle temperature (max.) 260 °C Bed temperature (min.) 90 °C Bed temperature (max.) 110 °C Recommended adhesion igus® adhesive film Construction space Closed installation space necessary Component cooling A component cooling is not necessary, with cooling switched on it is also possible to print Filament Brand: iglidur® Filament Colour: White Filament Diameter: 1.75mm Shipping Notes: Ready for shipping in 2-3 working days Brand: igus® Condition: New Product Code: IG-1180-175-750-WHI Weight: 0.75kg Customer reviews No reviews left yet Write a review Most RecentTop Rated No reviews have been left for this product, be the first to leave a review Related Products iglidur® I180-BL-PF 3D Printing Filament 1.75mm 750gms Black £79.00 £94.80 (inc. VAT) Add to cart Quickview iglidur® I180-BL-PF Black 3D Printing Filament 1.75mm 250gms £42.00 £50.40 (inc. VAT) Add to cart Quickview iglidur® I180-PF 3D Printing Filament 1.75mm 250gms White £42.00 £50.40 (inc. VAT) Add to cart Quickview
