Call Us Today (01702) 611027 9am - 5:30pm
Quick & Friendly Customer Service
Fast & Free Delivery
Order 2 spools B4 3PM Receive Next Day, Mon - Fri UK (Exc weekends)

Matte Wood fibre by Proto pasta

Matte Fiber HTPLA Chestnut Wood 1.75mm 500gms 3D printing filament

Matte Fiber HTPLA Chestnut Wood 1.75mm 500gms 3D printing filament

£26.00 £31.20 (inc. VAT)
Stock Status: In Stock
A Darker Wood Like HTPLA from Proto-pasta of the USA.
You Will Earn 31 points with this purchase
Laybuy

Make 6 weekly payments of £5.20.

Interest free. Learn More

PayPal Checkout

 

Premium Wood Finish

  • A classic brown with elegant sheen and sophisticated texture
  • Chestnut is lighter than Walnut and less red than Mahogany
  • Great for rigid, artistic prints with no special hardware required
  • An Endless Pastabilities filament with inspiration from nature
  • Designed & produced by Protoplant, makers of Protopasta

An extension of our Matte Fiber line, these rich colours are enhanced with small black flecks to create a wood-like appearance. Ranging from a beautiful soft yellow to deep, dark walnut, we’ve covered the spectrum and are excited to share their beauty with all of you!

Like our other HTPLAs, HTPLA can be "Heat Treated"  to increase crystallinity for "Higher Temperature" resistance compared to amorphous PLA, ABS, and co-polyesters like PETG!  Glitter Flake HTPLA prints translucence, but turns opaque when heat treated (or crystallised).  With a more crystalline structure, heat treated HTPLA parts can hold form to near melting, though temperatures where the material is practically useful vary greatly depending on geometry and load conditions!


For this improved the performance, your prints should be baked in an oven until you see a change from translucent to opaque with reduced gloss.  This visual change indicating the improved performance! We've  seen the change take place in 5-10 minutes on thin walled parts but can take an hour or more.  We've had good luck in a quality, at home convection oven at 110C (225F).  Parts will get very "floppy" before becoming more firm, so please leave supports on your parts or support them and bake them on a flat, non-radiating surface (like glass, ceramic, or composite).

  • Available in 1.75 & 2.85 (3) mm diameter on a 500g diameter recyclable cardboard spool
  • Usable on most PLA-compatible printers, such as Lulzbot, Makerbot, FlashForge, Dremel, Ultimaker, Printrbot, and more!

No abrasive fillers so expect normal wear with standard nozzles.

In our experience, good results were achieved using standard PLA parameters ranging from 195-225C nozzle with standard build surface preparation (blue tape, glue stick, Lokbuild or PrintBite). No heated bed required but up to 60C is okay.  Beware, if the bed temperature is too high, your part base could actually heat treat while printing, increasing warping and decreasing adhesion.  Some shrinkage will occur in the heat treating process, so dimension critical parts may need to be scaled appropriately (as much as 2.5% in our experience).

  • Filament Brand:
    Proto-pasta
  • Filament Type:
    PLA
  • Filament Colour:
    Brown
  • Filament Diameter:
    1.75mm
  • Filament Weight:
    500gms
  • Brand:
    Proto-pasta
  • Condition:
    New
  • Product Code:
    PRO-MFCW500-1.75mm
  • Weight:
    0.5kg
product review overlay image

Customer reviews

No reviews left yet
Write a review

No reviews have been left for this product, be the first to leave a review